#How to install emmanuel tv on dstv decoder settings manual#

Once you press OK, the manual installation setup will begin. Select the home network option and later the launch installation wizard alongside it. If the decoder finishes the scanning step, you can proceed to call Multichoice agents so that they activate your decoder. The DStv dish settings will help you get a strong signal and have your decoder registered.

Contact Multichoice to activate the decoder.

You should wait for the three tuners to show blue bars of the signal before you initiate the scan. Follow the steps in the wizard and make sure to use Quick Setup. Once you have connected the Explora decoder correctly to the satellite dish, run the installation wizard. Use that port to connect the RG6 cable from the dish. If you want to run the manual installation wizard on your DStv decoder, then follow the basic steps below: Switch on your decoder. Otherwise, your decoder will not get any signal.Īt the back of your decoder, there is a port written: “Unicable in”. Also, the two wires on the F-connector should never come into contact. On the smart LNB, connect the RG6 cable on the Unicable port using an F-connector.

Connect the RG6 cable to the unicable port on the Smart LNB.

These means do not mount your dish where there are trees and tall buildings which can reduce your DStv signal strength.

#How to install emmanuel tv on dstv decoder settings free#

Make sure you mount the satellite dish at a place that is free from obstructions that block the DStv signal. To check if your decoder can receive free channels, use a remote and check the Satellite Settings as shown: Go to Settings.

Mount and correctly align the satellite dish To check the Installation settings, get a DStv remote, and navigate through the setting in this order: Settings > Satellite Settings > Home Network > Launch Installation Wizard.

We recommend that you have your VCR Video Machine serviced once every two years.

Do not use earbuds or cotton wool to clean your video heads.

They can cause snow or loss of sound or picture. So long your satellite is pointed towards 36° East. Incorrect placing of oil will cause damage and unnecessary expense. Any DStv decoders can view the CCTV channels whether your subscription is expired or not.

#How to install emmanuel tv on dstv decoder settings password#

Never put oil in your VCR Video Machine. Choose INSTALLATION and press OK on the remote and input password (0000) which is a default strong decoder password.

Home Network Dstv IS20 PLEASE DO NOT CHANGE THE DEFAULT VALUES (Frequency should be 11594 and Symbol rate 27500 ) Press P+ button on the remote to access new networks.

#How to install emmanuel tv on dstv decoder settings how to#

This post is about how to connect two TV sets to a Gotv or The standard Dstv decoder. When Prompted, you need to Enter Pin code 9949. Press menu,advanced options,dish installation GO TO HOME NETWORK CHANGE LNB HIGH FREQUENCY FROM 10700 TO 10600. WATCH CHRIST TV ON YOUR DSTV DECODER Press menu Advanced options Dish Installation. Never try joining a broken tape this will damage your VCR video heads. See more of Emmanuel Makandiwa on Facebook.Throw away any tape that is crinkled or disc that is scratched.Never leave your tapes in the sun or on top of a warm TV, DSTV, VCR, DVD or CD Player.Do not use scratched discs, this causes audio tracks to skip, pictures to freeze and laser pickups to wear out sooner.

Do not use damaged cassette tapes, they will dirty your video heads.

Our experience has shown that many VCR (Video Machine) problems can be avoided by following these instructions:

Then check that you have selected the correct SOURCE or INPUT on the TV by using the TV remote control.ĭepending on which input socket your cable is connected to, select one of the following:.Depending on which input socket your cable is connected to, select one of the following: There is also another situation that requires you to connect two TV sets to one Gotv or the standard Dstv decoder.Check that the RCA cables from your TV is connected properly to the Video Machine RCA sockets.Once scanning is complete press the BLUE DSTV button. Make sure the following codes are all the same on Network 2: Enable Network: Yes. Check if there is power to the Video Machine Go to Satellite Settings > Additional Settings press OK.Check if there is power to the Television set.